Is There Fluoride in Washington Water?

DetoxWater Editorial Team•Published November 5, 2026

Yes, for most residents, because 65.1% of people served by Washington community water systems received fluoridated water in 2020. That statewide figure does not tell you what is in your tap today. For other locations, see fluoride in tap water by city.

How much of Washington’s water is fluoridated?

In 2020, 65.1% of people on Washington community water systems received fluoridated water, according to CDC water fluoridation data. The percentage describes people served by those systems, not the share of utilities that fluoridate or the share of water samples containing fluoride.

It also does not describe every Washington resident’s water source. If you use a private well, the community-system percentage does not tell you the fluoride concentration in your water.

The statewide figure is from 2020, so it should not be treated as a current reading for your home. A utility’s current water report or a water test is more useful for an individual address.

What is Washington’s law or policy on fluoridation?

The CDC statistic does not establish whether Washington has a statewide fluoridation mandate or describe the policy for a particular utility. It should not be used as a substitute for checking current state or local requirements.

For a current policy answer, contact the Washington State Department of Health or your water utility. Ask whether a state requirement, local decision or utility policy applies to your service area, and request its effective date.

Fluoride can also occur naturally in source water. Its natural presence alone does not establish that a water system practices fluoridation; ask the utility whether it adjusts fluoride as well as what concentration it measures.

How can you find out about your city or utility?

Start with the name of your water provider on your bill. If your water is included in rent or managed by a building, ask the landlord or property manager which system serves the address.

Look for the provider’s latest drinking water quality report, sometimes called a consumer confidence report. If fluoride is listed, check the concentration, the sampling year or reporting period, and whether the number is an average, a range or an individual result. Ask the provider which results apply to your address, especially if it uses more than one water source.

You can also contact the utility directly. Ask whether it adjusts fluoride, what fluoride concentration it most recently reported, when that water was sampled and whether the result represents your service area. A policy answer and a measured concentration answer different questions, so it is useful to request both.

For a private well, arrange a laboratory test that specifically includes fluoride and follow the lab’s sampling instructions. Our guide to testing water quality at home explains how to approach testing; ask the lab to report fluoride in milligrams per liter so the result is easy to compare with the benchmarks below.

If you are considering treatment, do not assume every filter removes fluoride. Check a product’s fluoride-reduction certification, capacity and replacement instructions; our guide to the best pitcher water filters can help you compare options.

What do the fluoride levels mean?

These benchmarks serve different purposes. They are not measurements of Washington’s water or a substitute for a local result.

BenchmarkFluoride levelWhat it represents
U.S. Public Health Service recommendation0.7 mg/LRecommended level for community water fluoridation
EPA secondary standard2.0 mg/LA secondary drinking water standard, not the federal enforceable maximum
EPA maximum contaminant level4.0 mg/LThe federal enforceable limit for public drinking water systems

The 0.7 mg/L recommendation is not the same kind of number as EPA’s 4.0 mg/L limit. The 2.0 mg/L secondary standard is a separate benchmark and is not the federal maximum contaminant level.

When comparing a report or test result, check that it uses the same units: milligrams per liter, written as mg/L. Fluoride in a sample can come from the water source, an adjustment by the utility or both; the concentration alone does not establish its source.

If a result is unclear, ask the utility or laboratory to explain the sampling date, the result’s basis and how it compares with the relevant standards. A single household result does not by itself establish whether a public system complies with its monitoring requirements.

Where does the Washington data come from?

The statewide percentage comes from the CDC’s Water Fluoridation Reporting System data for 2020. It reports the proportion of Washington’s community water system population receiving fluoridated water; it is not a measurement at an individual tap.

The benchmarks come from U.S. Public Health Service and EPA drinking water guidance and regulations. Because those benchmarks and the CDC percentage answer different questions, compare a specific water result with the standards rather than treating the statewide percentage as a fluoride concentration.

For the most relevant local information, use the latest report from the system serving your address or a laboratory result for your well. Check the sampling year whenever you compare results over time.

Who should you ask about fluoride questions?

If you have questions about fluoride in your drinking water, ask a dentist or doctor. Share your utility’s latest report or a laboratory result so they can discuss your situation.

Frequently asked questions

Can a Washington private well contain fluoride without it being added?

Yes. Fluoride can occur naturally in groundwater. A laboratory test can determine the concentration in a particular well.

Does boiling tap water remove fluoride?

No. Boiling does not remove fluoride and can concentrate it as water evaporates.

Does clear tap water mean it has no fluoride?

No. Appearance does not establish the fluoride concentration. Check your utility’s report or have the water tested.