Is There Fluoride in Utah Water?

DetoxWater Editorial Team•Published November 5, 2026

No, not anymore: Utah law ended the addition of fluoride to public water systems on May 7, 2025; before that, 50.9% of Utah’s public water system population received fluoridated water in 2020. Fluoride can still occur naturally in water, so the end of fluoridation does not mean every water source is fluoride-free. For a broader comparison, see fluoride in tap water by city.

How much of Utah’s water was fluoridated?

In 2020, 50.9% of Utah’s population served by public water systems received fluoridated water, according to the CDC’s state and county fluoridation data. The percentage describes people served by public systems, not the percentage of individual water sources or all Utah residents.

That figure predates the 2025 law. It is a historical measure of fluoridation, not a current measurement of fluoride concentration in a particular city’s water. It also does not tell private well owners what is in their water.

What is Utah’s law on adding fluoride to water?

Utah’s H.B. 81, Fluoride Amendments, prohibits adding fluoride to public water systems. The law took effect on May 7, 2025, according to a Murray City utility notice and the Utah League of Cities and Towns’ 2025 session recap.

The distinction is between added fluoride and fluoride that occurs naturally in a water source. The prohibition addresses addition to public water systems; it does not establish a measured fluoride level for every source. For the authoritative legal text, consult the Utah Legislature’s record for H.B. 81.

An older utility result may reflect fluoride that was added before the law took effect, naturally occurring fluoride, or both. Check the sampling date and ask the utility how to interpret that result rather than assuming it describes the water you receive now.

How can I check my city or water utility?

Start with the name of the public water system on your bill or contact your city or utility. Ask for its most recent water quality report and look for fluoride results, the sampling date and the unit of measurement. Fluoride concentrations are commonly reported in milligrams per liter, written as mg/L.

A useful question is: “What is the most recent measured fluoride concentration for the water supplied to my address?” If the utility uses more than one source, ask whether the reported result applies to your service area. A statewide percentage cannot answer that address-specific question.

If you use a private well, the public system’s report will not measure your well water. Ask a qualified laboratory about a fluoride test, including how to collect the sample and how it will report the result. Our guide to how to test water quality at home explains how to approach testing.

If you are considering a filter, check the specific model’s documentation for fluoride reduction rather than assuming every pitcher removes it. The best pitcher water filters guide is a starting point for comparing models.

What do the fluoride levels and standards mean?

The following numbers are reference points, not measured concentrations for Utah or for your utility:

LevelWhat it means
0.7 mg/LU.S. Public Health Service recommended level for community water fluoridation.
2.0 mg/LEPA secondary standard, which is not federally enforceable.
4.0 mg/LEPA maximum contaminant level, an enforceable limit for public water systems.

The 0.7 mg/L recommendation is a level for community water fluoridation, not proof that a Utah system currently adds fluoride or that your water measures at that level. The EPA standards are separate from that recommendation. To compare your water with these reference points, first obtain a result for your own source and check its sampling date and units.

Who should I ask about fluoride?

If you have questions about fluoride in your drinking water, ask a dentist or doctor.

Where does the Utah data come from?

The historical percentage comes from CDC community water fluoridation reporting and describes the public water system population in 2020. It should not be read as a current statewide concentration or as a result for an individual utility.

The policy information comes from Murray City’s 2025 notice and the Utah League of Cities and Towns’ 2025 legislative recap, rather than a measurement of water. Neither source gives a current fluoride concentration for every Utah system. Your utility’s report or a test of your own well is the appropriate place to look for a local measurement.

Frequently asked questions

Does boiling water remove fluoride?

No. Boiling does not remove fluoride and can concentrate it as water evaporates.

Can I tell whether water contains fluoride by taste?

Taste is not a reliable way to determine the fluoride concentration. Use a utility result or a laboratory test instead.