Is There Fluoride in Tacoma Water?

DetoxWater Editorial Team•Published November 5, 2026

Yes, Tacoma Water adds fluoride; the mean in finished-water samples with detectable fluoride was 0.73 mg/L in 2012–2019.

That means Tacoma has added fluoride, rather than only naturally occurring fluoride. For a broader comparison, see fluoride in tap water by city.

Does Tacoma Water add fluoride?

Yes. Tacoma Water’s 2025 water quality report states, “We currently fluoridate at a level of 0.7 ppm.” In water, 0.7 ppm is approximately 0.7 mg/L.

Fluoridation means the utility adds fluoride. That is different from a water supply containing only fluoride that occurs naturally in its source water. The utility’s statement establishes that Tacoma Water fluoridates; it does not mean every sample at every tap will have exactly the same concentration.

How much fluoride is in Tacoma water?

The utility’s reported level and the historical monitoring results describe different things. The 2025 report states a fluoridation level of 0.7 ppm, while the EPA compliance-monitoring data summarize finished-water samples collected in 2012–2019.

Tacoma Water figureLevelYear and basis
Utility-reported fluoridation level0.7 ppm, approximately 0.7 mg/L2025 report statement
Mean of samples with detectable fluoride0.73 mg/L2012–2019 finished-water compliance samples
Maximum measured level0.88 mg/L2012–2019 finished-water compliance samples

The historical record contains 30 samples, of which 22 had detectable fluoride. The 0.73 mg/L figure is the mean of those detected samples, not necessarily the mean of all 30 samples. Neither historical figure is a measurement of your tap water today.

Reference levelConcentrationWhat it represents
US Public Health Service recommendation0.7 mg/LRecommended level for community water fluoridation
EPA secondary standard2.0 mg/LA non-enforceable federal standard
EPA maximum contaminant level4.0 mg/LAn enforceable federal limit

The historical mean of 0.73 mg/L was slightly above the 0.7 mg/L recommendation. Both the historical mean and the 0.88 mg/L maximum were below the two EPA standards. These comparisons do not replace a current test of water at your address.

What is the county and Washington state context?

In 2020, 65.1% of Washington’s population served by public water systems received fluoridated water, according to CDC water fluoridation data. That figure describes the public-water-system population, not necessarily every Washington resident.

The statewide percentage does not establish the percentage for Pierce County or the status of any particular water system there. For an address outside Tacoma Water’s service, identify the actual supplier and check its report rather than assuming it has Tacoma Water’s fluoride level.

What does Washington law say about fluoridation?

The sources cited here do not establish whether Washington law requires, permits or restricts fluoridation in a particular situation. Tacoma Water’s report establishes what that utility says it does; it should not be treated as a statement of statewide law.

For a current answer about state requirements or local decisions, ask the Washington Department of Health or the water supplier serving the address. If you need the rules for a particular property, have the supplier’s name and address ready when you ask.

How can you check your water or remove fluoride?

Start by identifying your water supplier. A water bill or the property owner may help, and the supplier can tell you which water quality report applies to your address. Check the report’s sampling year and whether a listed figure is a measured result or a reported operating level.

For a measurement at your tap, use a laboratory that tests drinking water for fluoride. Ask for its sampling instructions, the cost and the reporting units before collecting a sample. Our guide to how to test water quality at home explains how to approach water testing.

If you want to reduce fluoride, look for a treatment device specifically certified for fluoride reduction. Some reverse-osmosis systems and other products make that claim, but certification and performance depend on the individual model. An ordinary filter or pitcher should not be assumed to remove fluoride merely because it filters water; compare the claims in our guide to the best pitcher water filters.

Follow the manufacturer’s installation and replacement instructions. If knowing the result matters to you, test water after treatment as well as before it: the Tacoma-wide historical figures cannot tell you how much fluoride a device removes at your tap.

Who should you ask about fluoride?

Ask a dentist or doctor if you have questions about fluoride in your drinking water.

Where does the data come from?

Three sources serve different purposes. Tacoma Water’s 2025 report supplies the utility’s statement that it fluoridates. EPA’s 2012–2019 compliance-monitoring data supply the historical sample count, detected-sample mean and maximum for Tacoma Water.

The CDC dataset supplies the 2020 Washington-wide percentage. The US Public Health Service recommendation and EPA standards are reference points for interpreting concentrations; they are not measurements of Tacoma water.

Frequently asked questions

Does boiling Tacoma water remove fluoride?

No. Boiling does not reliably remove fluoride, and evaporation can increase its concentration in the remaining water.

Can I tell how much fluoride is in water by looking at it?

No. A clear glass of water does not tell you its fluoride concentration; a fluoride test is needed.

Is 0.73 mg/L the same as 0.73 ppm in water?

Approximately. For dilute concentrations in water, 1 mg/L is approximately equal to 1 ppm.