Is There Fluoride in South Dakota Water?
Yes, for most residents: 93.8% of people on South Dakota community water systems received fluoridated water in 2020.
That statewide figure does not establish the fluoride level at a particular address. For comparisons with other locations, see fluoride in tap water by city.
How much of South Dakota’s water is fluoridated?
In 2020, 93.8% of the people served by South Dakota community water systems received fluoridated water. The figure describes people served by those systems, not the percentage of utilities that fluoridate their water.
It is also not the percentage of all South Dakota residents receiving fluoridated water. People who obtain drinking water outside community water systems, such as from private wells, are not included in that population measure.
Fluoride can occur naturally in source water. Natural fluoride is not the same as fluoride added through community water fluoridation, and a concentration reported on its own does not establish whether a utility adds fluoride.
What is South Dakota’s law or policy on fluoridation?
The information available here does not establish whether South Dakota law requires, allows or restricts community water fluoridation. The statewide coverage figure also does not identify who makes that decision for an individual water system.
For current requirements, ask the state drinking water program. For the practice at your address, ask the utility that serves you whether it adds fluoride and whether its source water contains naturally occurring fluoride. Those are separate questions: a reported fluoride concentration does not, by itself, identify its source.
How can you find the fluoride level in your own water?
Start with the supplier serving your address rather than assuming that the statewide percentage applies to your tap. A water bill, the property owner or a building manager can help you identify the supplier.
- Find the utility’s water quality report. Ask for its most recent consumer confidence report, the annual drinking water report for its customers. Look for the fluoride entry and the units used to report it.
- Check the sampling details. Note the sampling year, concentration and any range shown. The year a report is published may differ from the year the water was sampled.
- Ask about your address. If the utility uses more than one water source, ask which results represent your service area. A system-wide figure or range is not necessarily a measurement from your tap.
- Ask whether fluoride is added. A utility may be able to explain both its fluoridation practice and the contribution from naturally occurring fluoride. Request a recent reported concentration as well as the sampling date.
- Test a private well if you need a result. Contact a laboratory that tests drinking water for fluoride and follow its collection instructions. A lab result describes the sample tested, not every well in the area.
For more on collecting and interpreting a sample, see how to test water quality at home. If you are considering a filter, check whether the specific model is independently certified for fluoride reduction; the best pitcher water filters are a starting point for comparing products.
What do the fluoride levels and standards mean?
The values below are national reference levels, not measurements of South Dakota water. Concentrations are expressed in milligrams per liter (mg/L).
| Value | What it means |
|---|---|
| 0.7 mg/L | The US Public Health Service’s recommended fluoride concentration for community water fluoridation. It is a recommendation, not the EPA’s maximum limit. |
| 2.0 mg/L | The EPA’s secondary standard for fluoride. Secondary standards are federally non-enforceable guidelines. |
| 4.0 mg/L | The EPA’s primary maximum contaminant level for fluoride, an enforceable limit for public water systems. |
These numbers have different purposes, so a utility report should be read alongside the label for each value. The EPA public-water-system limit is not a measurement of a private well.
If you have questions about fluoride in your drinking water, ask a dentist or doctor.
Where does the South Dakota data come from?
The statewide percentage comes from the CDC’s community water fluoridation data, reported through its Water Fluoridation Reporting System. The South Dakota figure cited here is for 2020 and is based on the population served by community water systems.
That figure is useful for statewide context, but it is not a current concentration measured at an individual address. The national reference values above come from the US Public Health Service and EPA drinking water standards. For a local concentration, use the sampling date and result in your utility’s report or a laboratory report for your own sample.
Frequently asked questions
Can you tell whether water contains fluoride by tasting it?
Taste is not a reliable way to determine a water sample’s fluoride concentration. Check the utility’s report or have a sample tested.
Does the statewide percentage include bottled water?
No. It describes people served by community water systems, not bottled-water purchases or consumption.
Can apartment residents ask for their water utility’s report?
Yes. Ask the property manager which utility serves the building, then request its water quality report or look for it on the utility’s website.