Is There Fluoride in Simi Valley Water?

DetoxWater Editorial Team•Published November 5, 2026

Yes, water supplied by Ventura WWD No. 8 – Simi Valley has added fluoride, and its detected-sample mean was 0.12 mg/L in 2014–2019.

Does Simi Valley’s water contain added fluoride?

The CDC’s 2025 fluoridation status report lists Ventura WWD No. 8 – Simi Valley as fluoridated, with a status of “Consecutive.” A consecutive system receives water from another water system; the listing does not establish that Ventura WWD No. 8 adds fluoride itself.

Fluoride can also occur naturally in water. A measurement showing fluoride does not, by itself, establish whether fluoride was added; the CDC’s fluoridated designation is separate from the historical measurements discussed below.

The designation identifies a particular water system, so check your water bill or ask your supplier if you are unsure whether Ventura WWD No. 8 serves your address. For other locations, see fluoride in tap water by city.

How much fluoride was measured in Simi Valley water?

The historical local level is an unweighted mean of detected finished-water compliance samples, not a current tap reading. In the EPA’s Six-Year Review 4 monitoring data, five finished-water samples for Ventura WWD No. 8 – Simi Valley were recorded for 2014–2019; two detected fluoride.

Measurement or referenceFluoride levelBasis
Simi Valley detected-sample mean0.12 mg/LUnweighted mean of detected finished-water samples, 2014–2019
Simi Valley sample maximum0.14 mg/LMaximum reported sample result, 2014–2019
U.S. Public Health Service recommendation0.7 mg/LRecommended level for community water fluoridation
EPA secondary standard2.0 mg/LNon-enforceable secondary drinking-water standard
EPA maximum contaminant level4.0 mg/LEnforceable drinking-water limit

The historical mean and maximum were below all three reference levels. The 0.7 mg/L figure is a recommendation for community water fluoridation, not a measurement of what was in Simi Valley water.

The older entry-point results may include water from unfluoridated sources or may predate current practices. The mean covers the detected samples rather than all five samples, and it is not necessarily the average concentration delivered to every home.

These historical results do not establish today’s fluoride concentration or a current compliance determination. The CDC’s later status listing identifies the system’s fluoridation status but does not measure the fluoride level at your tap.

How does Simi Valley compare with Ventura County and California?

In 2020, the CDC’s state and county data reported that 94.6% of Ventura County’s public-water-system population received fluoridated water. The corresponding California figure was 57.5%.

These percentages describe people served by public water systems, not the percentage of water sources containing fluoride or the concentration at an individual tap. They provide county and state context rather than a separate measurement for Simi Valley.

The county figure also does not identify which supplier serves a particular address. Check your own supplier’s report for information about your water system.

What is California’s policy on fluoridation?

The available data do not identify an applicable California state fluoridation policy for Ventura WWD No. 8 – Simi Valley. The system’s CDC status listing does not explain which legal requirements or funding arrangements apply to it.

For current rules and their application to your supplier, ask the California State Water Resources Control Board’s Division of Drinking Water or your water supplier. A countywide coverage percentage does not establish the legal basis for an individual system’s status.

How can you check your water or remove fluoride?

Start with your water bill to identify your supplier, then ask for its latest consumer confidence report and the most recent fluoride monitoring results. Ask whether those results represent water delivered to your service area, when the samples were collected, and whether the report includes a range as well as an average.

For a measurement at your own tap, use a laboratory that tests drinking water for fluoride and follow its sampling instructions. Check the laboratory’s reporting limit and units so you can interpret the result; how to test water quality at home explains how to plan a water test.

If you want to remove fluoride, look for a filter specifically certified for fluoride reduction. Some reverse-osmosis systems and some other filters are certified for that purpose, but not every pitcher or cartridge removes fluoride.

Check the exact model’s certification and replace filters according to the manufacturer’s instructions. The guide to the best pitcher water filters can help you compare options, but verify fluoride reduction for the particular model you choose.

If you have questions about fluoride in your drinking water, ask a dentist or doctor.

Where does the data come from?

The local fluoridation designation comes from the CDC’s 2025 system status report. The county and state percentages come from CDC reporting for 2020, while the local concentration figures come from older EPA compliance-monitoring samples collected during 2014–2019.

These sources answer different questions: status indicates whether the system is classified as fluoridated, population percentages describe coverage, and samples show measured concentrations at particular times. Your supplier’s latest report or a tap test is the better starting point for checking current conditions.

Frequently asked questions

Does boiling Simi Valley tap water remove fluoride?

No. Boiling does not remove fluoride and can concentrate it as water evaporates.

Can you tell whether water contains fluoride by looking at it?

No. Clear water can contain fluoride; a test is needed to measure its concentration.

Is 1 mg/L the same as 1 ppm in water?

For dilute substances in water, 1 mg/L is approximately 1 part per million, or ppm.