Is There Fluoride in San Antonio Water?
Yes, the San Antonio Water System adds fluoride; its measured mean was about 0.47 mg/L in 2012–2019. That figure is an unweighted mean of detected finished-water compliance samples, not a current reading from every tap. Compare other locations in our guide to fluoride in tap water by city.
Is fluoride added to San Antonio water?
The CDC’s 2025 fluoridation status report identifies the San Antonio Water System as fluoridated. The listed fluoride product is fluorosilicic acid, H2SiF6.
Added fluoride is distinct from fluoride that occurs naturally in a water source. The system’s reported status means fluoride is added; it does not merely indicate that a sample contained naturally occurring fluoride.
The status applies to the named public water system. To confirm the information relevant to your address, check your water bill or ask your water provider which system serves you.
How much fluoride is in San Antonio water?
The historical measurements below come from EPA’s Six-Year Review 4 compliance monitoring data. They are compared with federal reference values, which have different purposes.
| Measurement or reference | Fluoride level | Basis |
|---|---|---|
| Historical mean | 0.47 mg/L | Unweighted mean of 92 detected finished-water samples from 2012–2019 |
| Historical maximum | 0.95 mg/L | Highest finished-water sample result from 2012–2019 |
| US Public Health Service recommendation | 0.7 mg/L | Recommended level for community water fluoridation |
| EPA secondary standard | 2.0 mg/L | Nonenforceable federal guideline |
| EPA primary limit | 4.0 mg/L | Enforceable maximum contaminant level |
The EPA data include 93 finished-water compliance samples across system entry points in 2012–2019, of which 92 had detectable fluoride. The mean gives equal weight to detected samples rather than weighting them by the number of customers served or the volume of water delivered.
The historical mean was below 0.7 mg/L, while the historical maximum was above it. Both were below the EPA values shown. The 0.7 mg/L recommendation is not the same kind of value as EPA’s enforceable 4.0 mg/L limit.
These older samples may include unfluoridated sources or predate current practice. Neither the historical mean nor the maximum establishes the fluoride level at your tap today or, on its own, establishes current regulatory compliance.
How do Bexar County and Texas compare?
In 2020, the CDC’s state and county fluoridation data reported that 94.7% of the public-water-system population in Bexar County received fluoridated water. The corresponding figure for Texas was 71.0%.
| Area | Public-water-system population receiving fluoridated water | Year |
|---|---|---|
| Bexar County | 94.7% | 2020 |
| Texas | 71.0% | 2020 |
These percentages describe people served by public water systems, not necessarily all residents. They are coverage figures rather than measurements of fluoride concentration. They also do not establish the current status of an individual address or water provider.
What does Texas law say about fluoridation?
The CDC coverage figures and system status report describe reported fluoridation, not the legal basis for it. They do not establish a Texas-wide requirement or prohibition on adding fluoride.
Federal concentration standards also do not, by themselves, tell you what Texas requires a particular provider to add. For current state law and local policy, ask Texas drinking-water regulators or your water provider for the applicable rule or utility decision. Identify your provider first so the answer can be matched to your service area.
How can you check or remove fluoride at home?
Start with your provider’s latest water quality report and look for the fluoride result, its sampling date, and any explanation of how the result was calculated. A system-wide result may not tell you the exact concentration at your own tap.
For an address-specific measurement, ask an accredited drinking-water laboratory about a fluoride test. Follow its sampling instructions and ask whether the result will be reported in mg/L. Our guide to how to test water quality at home explains how to approach testing.
If you want to reduce fluoride, reverse osmosis and distillation can do so; some activated alumina filters can also reduce it. Check the exact product’s independent certification and performance information for a fluoride-reduction claim. Do not assume an ordinary activated-carbon pitcher removes fluoride.
When comparing the best pitcher water filters, check the specific model rather than the brand alone. Follow its replacement schedule, and consider testing water before and after filtration if you want to check its performance at your tap.
When should you ask a dentist or doctor?
If you have questions about fluoride in drinking water for yourself or a child, ask a dentist or doctor.
Where does the information come from?
The CDC’s 2025 report supplies the San Antonio Water System’s fluoridation status, while its 2020 dataset supplies the county and state coverage figures. EPA’s 2012–2019 compliance data supplies the historical sample results.
Those sources answer different questions: whether the system was reported as fluoridated, how widely fluoridated water was supplied in a broader area, and what finished-water samples measured during an earlier period. For the latest information at your address, use your current provider’s report or an appropriately collected tap-water test.
Frequently asked questions
Does boiling water remove fluoride?
No. Boiling does not remove fluoride and can make it more concentrated as water evaporates.
What does mg/L mean on a water report?
It means milligrams per liter, a measure of the concentration of a substance in water.
Does the measured fluoride level show how much was added?
No. A measured fluoride concentration alone does not separate fluoride added by the utility from any fluoride naturally present in the source water.