Is There Fluoride in Provo Water?
No fluoride is added: Provo’s public water contains natural fluoride only, and the mean of detected finished-water samples was about 0.19 mg/L in 2015–2018.
Is fluoride added to Provo water?
Provo’s public water is not fluoridated, although natural fluoride can still be present. The CDC’s 2025 fluoridation status report lists PROVO CITY as not fluoridated and identifies its system as “consecutive.”
A consecutive system receives some or all of its water from another public water system. That designation describes the system’s water supply arrangement; it does not itself mean fluoride is added.
For comparisons with other locations, see fluoride in tap water by city. The Provo status applies to the public water system, not automatically to every private well or other water supply within the city.
How much fluoride has been measured in Provo water?
The EPA’s Six-Year Review 4 compliance monitoring data include four finished-water samples for PROVO CITY, collected in 2015 and 2018. Fluoride was detected in three of the four samples; the reported mean is based on those detections, not all four samples.
| Measure or comparison | Fluoride level | Basis |
|---|---|---|
| Provo detected-sample mean | 0.19 mg/L | Mean of detected finished-water compliance samples, 2015–2018 |
| Provo sample maximum | 0.24 mg/L | Highest finished-water compliance sample, 2015–2018 |
| US Public Health Service recommendation | 0.7 mg/L | Recommended level for community water fluoridation |
| EPA secondary standard | 2.0 mg/L | National secondary drinking water standard |
| EPA maximum contaminant level | 4.0 mg/L | Enforceable national drinking water limit |
Both historical Provo measurements were below the three comparison values. The 0.7 mg/L recommendation is a target for systems that add fluoride, not a requirement that naturally occurring fluoride reach that level; the EPA’s secondary standard is a guideline, while its maximum contaminant level is enforceable.
These measurements describe the samples collected in 2015 and 2018, not necessarily the concentration at a particular Provo tap today. A current utility report or a new test is more useful for checking your present supply.
How does Provo compare with Utah County and Utah?
In 2020, the CDC’s state and county fluoridation data reported that 5.9% of Utah County’s public-water-system population received fluoridated water. The corresponding figure for Utah was 50.9%.
Those percentages describe public-water-system populations, not the percentage of all residents or the fluoride concentration in their water. They are historical figures from before the 2025 statewide prohibition and should not be used as current estimates.
County and state figures also do not establish the status of an individual city system. For Provo specifically, the CDC’s 2025 system report is the more direct source for fluoridation status.
What does Utah law say about adding fluoride?
Utah’s H.B. 81, Fluoride Amendments, prohibits public water systems from adding fluoride to their water. According to a Murray City utility notice, the prohibition took effect on May 7, 2025.
The Utah League of Cities and Towns’ 2025 session recap also describes limits on local ordinances requiring or permitting fluoride to be added to public water systems. A prohibition on adding fluoride does not mean water contains no naturally occurring fluoride.
The Legislature’s official bill page was unavailable for confirmation. Check the enacted text with the Utah Legislature before relying on a legal interpretation of the law.
How can you check or remove fluoride from your water?
Start by confirming which public water system serves your address. Ask the utility for its latest drinking water quality report and fluoride results, including when and where the samples were collected. A system-wide result may not represent the exact concentration at your tap.
For a household-specific result, use a laboratory that tests drinking water for fluoride and follow its sampling instructions. Our guide to how to test water quality at home explains how to approach testing and interpret a report. If you use a private well, test that water rather than relying on Provo’s public-system results.
If you want to reduce fluoride, look for a reverse-osmosis system or another filter independently certified specifically for fluoride reduction. Not every pitcher or carbon filter removes fluoride, so check the product’s certified contaminant-reduction claims and follow its cartridge replacement instructions. See our guide to the best pitcher water filters when comparing options, and verify each model’s fluoride claim.
When should you ask a dentist or doctor?
If you have questions about fluoride in your drinking water, ask a dentist or doctor.
Where does the Provo fluoride data come from?
The status comes from the CDC’s 2025 report for PROVO CITY. The concentration figures come from EPA compliance samples collected in 2015 and 2018; they are measurements of finished water, not a new test of a household tap.
The county and state percentages come from the CDC’s 2020 dataset. The policy summary comes from the Murray City notice and the Utah League of Cities and Towns recap, so readers seeking the precise legal text should confirm it with the Utah Legislature.
Frequently asked questions
Does boiling Provo water remove fluoride?
No. Boiling does not remove fluoride and can increase its concentration as water evaporates.
What does mg/L mean on a fluoride report?
It means milligrams per liter, a measure of the mass of fluoride in a given volume of water.
Can a fluoride test tell whether the fluoride was natural or added?
A standard concentration result alone does not establish the fluoride’s source. Ask the water supplier about its source water and treatment practices.