Is There Fluoride in Milwaukee Water?

DetoxWater Editorial Team•Published November 5, 2026

Yes, Milwaukee’s utility adds fluoride; its state-reported operational level averaged about 0.64 mg/L in 2025.

Is fluoride added to Milwaukee water?

Milwaukee is reported as a fluoridated water system. The fluoride product identified for the system is H2SiF6, also called fluorosilicic acid.

Fluoride can occur naturally in water, but naturally occurring fluoride is not the same as a utility adding it. Milwaukee’s reported status is that fluoride is added. For comparisons with other communities, see fluoride in tap water by city.

How much fluoride is in Milwaukee water?

Milwaukee’s state-reported operational fluoride level was 0.64 mg/L in 2025, calculated as the mean of 12 monthly values. The lowest and highest reported monthly values were 0.63 mg/L and 0.67 mg/L, respectively, in 2025.

Level or standardFluoride concentrationWhat it represents
Milwaukee operational level0.64 mg/L2025 mean of 12 monthly values
Milwaukee monthly range0.63–0.67 mg/LLowest and highest reported monthly values in 2025
US Public Health Service recommendation0.7 mg/LRecommended level for community water fluoridation
EPA secondary standard2.0 mg/LNon-enforceable secondary drinking-water standard
EPA maximum contaminant level4.0 mg/LEnforceable drinking-water limit

The 2025 Milwaukee mean was slightly below the federal recommended level and below both EPA standards. These figures serve different purposes: the recommendation is a level for community fluoridation, while the EPA figures are drinking-water standards.

The monthly range describes reported operational values, not the lowest and highest results from individual household taps. The mean of monthly values is also not necessarily the same as a water-volume-weighted annual average.

What is the county and Wisconsin context?

In 2020, 100.0% of Milwaukee County’s public-water-system population was reported as receiving fluoridated water. The corresponding Wisconsin figure was 86.7% of the state’s public-water-system population.

Those percentages describe populations served by public water systems, not every resident or every water source. In particular, they should not be read as measurements from private wells. They also describe 2020, so they do not establish the current status of every system in the county or state.

The county figure provides context for Milwaukee, but it is not a separate measurement of the Milwaukee utility’s fluoride concentration. The utility’s 2025 operational level is the more relevant figure when comparing Milwaukee water with the federal levels above.

What does Wisconsin law say about fluoridation?

The available data do not specify Wisconsin’s state fluoridation policy or whether state law requires communities to add fluoride. Milwaukee’s reported status establishes that its utility adds fluoride; it does not, by itself, establish a requirement for every Wisconsin water system.

For a question about a particular address outside the Milwaukee system, identify the water supplier before applying Milwaukee’s status or level. A countywide percentage cannot substitute for that supplier’s own report.

How can you check or remove fluoride from your water?

Start by identifying your water supplier on your bill or asking your landlord or building manager. If your water comes from a private well, a city utility figure does not tell you the fluoride concentration in that well. Ask a qualified drinking-water laboratory for a fluoride test and follow its sampling instructions; our guide explains how to test water quality at home.

If you want to reduce fluoride, look for a treatment device independently certified for fluoride reduction. Reverse osmosis systems and some distillation or adsorption products can reduce fluoride, but performance depends on the specific product and its maintenance. Check the model’s certification and replacement instructions rather than assuming every filter removes it.

Some pitchers may be certified for fluoride reduction, while others are not. When comparing the best pitcher water filters, check the specific model’s certified claims. Testing water before and after treatment can help you check its performance at your tap.

If you have questions about fluoride in your drinking water, ask a dentist or doctor.

Where does the Milwaukee fluoride data come from?

The CDC fluoridation status report identifies Milwaukee’s system, WI2410100, as fluoridated in 2025. The CDC monthly fluoride levels report supplies the 2025 state-reported operational values used for the mean and range above.

The county and state percentages come from the CDC’s community water fluoridation dataset. Its population percentages and the utility’s operational measurements answer different questions, so they should not be treated as interchangeable.

Frequently asked questions

Does boiling Milwaukee tap water remove fluoride?

No. Boiling does not remove fluoride and can concentrate it as water evaporates.

Can a fluoride test tell whether fluoride was added or naturally occurring?

A concentration result alone does not identify the fluoride’s source. Check the water supplier’s fluoridation report as well.

Does every pitcher filter remove fluoride?

No. Check whether the specific pitcher and replacement filter are independently certified for fluoride reduction.