Is There Fluoride in Fort Worth Water?
Yes, Fort Worth’s utility adds fluoride, and finished-water samples collected from 2012 to 2019 had a measured mean of about 0.47 mg/L. For comparisons with other locations, see fluoride in tap water by city.
Is fluoride added to Fort Worth water?
Fort Worth’s public water system is listed as fluoridated in the CDC’s 2025 Fluoridation Status Report. The fluoride product reported for the system is H2SiF6, or fluorosilicic acid.
Fluoride can also occur naturally in water, but naturally occurring fluoride alone is not the same as a utility adding it. Fort Worth’s reported status is that the utility adds fluoride. That status describes the public water system, not every private well or separately operated water system in the area.
How much fluoride was measured in Fort Worth water?
The available historical measurements come from the EPA’s Six-Year Review 4 compliance monitoring data. The table compares them with federal reference levels; the measurements and standards do not all describe the same thing.
| Measure | Level | Basis |
|---|---|---|
| Fort Worth measured mean | 0.47 mg/L | Unweighted mean of detected finished-water entry-point compliance samples, 2012–2019 |
| Fort Worth measured maximum | 0.98 mg/L | Highest detected finished-water entry-point compliance sample, 2012–2019 |
| US Public Health Service recommendation | 0.7 mg/L | Recommended level for community water fluoridation |
| EPA secondary standard | 2.0 mg/L | Non-enforceable federal secondary drinking-water standard |
| EPA maximum contaminant level | 4.0 mg/L | Federal primary drinking-water limit |
All 38 finished-water samples in the 2012–2019 dataset had fluoride detections. The historical mean was below the recommended level, while the historical maximum was above it; both were below the two EPA standards shown.
The mean is an unweighted average across entry-point samples, not a current reading at a particular home. The older samples may include unfluoridated sources or predate current practice, so they cannot establish today’s concentration or current compliance.
How do Tarrant County and Texas compare?
The CDC’s 2020 state and county fluoridation data give broader context for people served by public water systems:
| Area | Public water system population receiving fluoridated water | Year |
|---|---|---|
| Tarrant County | 97.7% | 2020 |
| Texas | 71.0% | 2020 |
These percentages describe coverage, not the concentration of fluoride in Fort Worth water. The county figure is not a measurement for the Fort Worth utility alone, and neither percentage describes people outside public water system service.
What is Texas’s fluoridation policy?
Texas’s state fluoridation policy is not established by the data cited here. The utility’s reported status and the statewide coverage percentage describe fluoridation practice; neither, on its own, establishes a statewide legal requirement.
For a current policy question, contact the relevant water utility or check current Texas state rules. Keep a question about a legal requirement separate from a question about whether a particular system reports adding fluoride.
How can you check your water or remove fluoride?
First, identify the water system that serves your address. A utility bill or the utility’s customer service department can help; a Fort Worth address alone does not establish which system supplies a particular property. Fort Worth’s public water system identification number is TX2200012.
Ask your supplier for its latest drinking-water quality report and look for fluoride results and their sampling dates. A system report can provide useful context, but its results may not be a measurement from your own tap. For a tap-specific result, ask an accredited drinking-water laboratory for a fluoride analysis and follow its sampling instructions. See how to test water quality at home for more on choosing a test.
If you want to reduce fluoride, look for a treatment device independently certified for fluoride reduction. Reverse osmosis and activated alumina are treatment methods used for that purpose, but a device’s specific certification and performance claims matter more than its general filter category.
Check the product’s performance information, capacity and replacement schedule before buying. Do not assume every pitcher or refrigerator filter removes fluoride; compare the specific claims when reviewing the best pitcher water filters. If you want to verify a device’s performance at your tap, a lab can test water before and after treatment.
When should you ask a dentist or doctor?
If you have questions about fluoride in your drinking water or your fluoride intake, ask a dentist or doctor for advice.
Where does the Fort Worth data come from?
The CDC status report identifies Fort Worth’s public water system and reports its fluoridation status for 2025. The separate CDC state and county dataset provides the broader 2020 coverage percentages; those figures are not city-level concentration measurements.
The EPA dataset supplies the finished-water compliance sample results from 2012 to 2019. Because those results are historical and sampled at entry points, use a current utility report or a tap test if you need a more recent or address-specific answer.
Frequently asked questions
Does boiling Fort Worth water remove fluoride?
No. Boiling does not remove fluoride and can concentrate it as water evaporates.
Does a refrigerator filter necessarily remove fluoride?
No. Check the specific filter’s independent certification and performance information for a fluoride-reduction claim.
What does TX2200012 identify?
It is the public water system identification number for the City of Fort Worth system.