Is There Fluoride in Fort Collins Water?
Yes, the Fort Collins utility adds fluoride; its measured mean in finished-water compliance samples was 0.62 mg/L in 2012–2019.
For comparisons with other communities, see fluoride in tap water by city. The Fort Collins result is historical, not a measurement of what is coming from your tap today.
Does Fort Collins add fluoride to its water?
Yes. The CDC’s 2025 Fluoridation Status Report lists the Fort Collins city water system, identified as CO0135291, as fluoridated. That means the status reported here is added fluoride, not merely a finding that naturally occurring fluoride is present.
The status report and the measurement record answer different questions. The CDC report identifies whether the system was fluoridated in 2025; the EPA record gives the results of earlier finished-water samples. The 2025 status does not establish a measured concentration for that year.
How much fluoride was measured in Fort Collins water?
The EPA Six-Year Review 4 compliance data include 24 finished-water samples for the Fort Collins city system, all with detectable fluoride. The figures below summarize those samples, not a current reading or a test of an individual household tap.
| Measure | Result | Year and basis |
|---|---|---|
| Mean | 0.62 mg/L | 2012–2019 mean of detected finished-water compliance samples |
| Maximum | 0.88 mg/L | Highest detected result among finished-water compliance samples from 2012–2019 |
Here is how those historical results relate to the federal reference values:
| Federal reference | Level | What it is |
|---|---|---|
| US Public Health Service recommendation | 0.7 mg/L | Recommended level for community water fluoridation, not a regulatory limit |
| EPA secondary standard | 2.0 mg/L | A non-enforceable secondary drinking-water standard |
| EPA primary limit | 4.0 mg/L | An enforceable drinking-water limit |
The historical mean was below all three values. The historical maximum was above the recommended level but below both EPA standards.
These comparisons involve different kinds of numbers: a mean, a highest sample result, a recommended level and regulatory benchmarks. They do not by themselves establish the concentration at your tap today or determine the system’s current compliance status.
How does Fort Collins compare with Larimer County and Colorado?
In 2020, 93.3% of the Larimer County population served by public water systems received fluoridated water. The corresponding figure for Colorado was 75.2%, according to the CDC’s state and county fluoridation data.
Those figures describe populations served by public water systems, not necessarily every resident or every water source in the county or state. They provide context for Fort Collins but do not measure fluoride in the Fort Collins city system or identify the status of a particular home’s water supply.
What are Colorado’s fluoride laws and policies?
The available records do not establish Colorado’s current law or policy on community water fluoridation. They also do not establish whether a state or local requirement applies to the Fort Collins city system.
The CDC’s system status and population figures describe reported fluoridation; they are not a statement of the legal rules. For a legal or policy question, check current state and local requirements rather than treating the reported status as proof of a mandate.
How can you check or remove fluoride from your water?
First, identify your water supplier. A city-system report is relevant if that system serves your address, but county and state percentages cannot confirm which system supplies a particular tap. If you use a private well, the city-system measurements do not describe your well water.
For a public supply, look for the supplier’s latest drinking-water quality report and find the fluoride entry. Check the reporting year, the units and whether the figure is an average, a range or a single result. You can also ask the supplier for its most recent fluoride information and how the reported result was calculated.
For a measurement at your own tap or well, use a laboratory that tests drinking water for fluoride and follow its sample-collection instructions. Our guide to how to test water quality at home explains how to approach a water test. A test describes the sample collected, so ask the laboratory or supplier how to interpret it if you need a longer-term picture.
If you want to reduce fluoride, look for a treatment device independently certified for fluoride reduction. Reverse osmosis and distillation are among the methods that can remove fluoride; check the specific product’s certification and maintenance instructions rather than assuming every device works the same way. Some pitchers have specific reduction claims, so check the model’s listing when comparing the best pitcher water filters.
Boiling water does not remove fluoride and can concentrate it as water evaporates. If you have questions about fluoride in drinking water, ask a dentist or doctor.
Where does the data come from?
The CDC status report identifies the Fort Collins city system and its reported 2025 fluoridation status. The CDC state and county dataset supplies the 2020 population percentages, which are broader context rather than city-system measurements.
The EPA compliance dataset supplies the 2012–2019 finished-water results for the system identified as CO0135291. Its mean and maximum are useful historical reference points, but a newer supplier report or a fluoride-specific test is needed to investigate a more recent concentration.
Frequently asked questions
What does mg/L mean on a fluoride report?
It means milligrams of fluoride per liter of water, a measure of concentration.
Can you tell whether water contains fluoride by taste?
Taste alone cannot establish whether fluoride is present or measure its concentration. Use a fluoride-specific water test for a result.
Will a filter labeled for chlorine necessarily remove fluoride?
No. Look for a specific, independently certified fluoride-reduction claim for the filter model.