Is There Fluoride in Denton Water?
Yes, Denton’s utility adds fluoride; the measured mean of detected finished-water samples was 0.37 mg/L in 2012–2019. That historical measurement is not a current reading from your tap. For other locations, see fluoride in tap water by city.
Does Denton add fluoride to its water?
Yes. The CDC’s 2025 fluoridation status report lists the City of Denton water system as fluoridated. The listed fluoride product is fluorosilicic acid, H2SiF6.
Fluoride can also occur naturally in water. Its natural presence is different from a utility adding a fluoride product; Denton’s reported status is that the utility adds it.
The City of Denton system is identified as TX0610002. If your address is served by another public water system or a private well, the City of Denton’s status and historical measurements may not describe your water.
How much fluoride has been measured in Denton water?
The EPA’s Six-Year Review 4 compliance monitoring data show an unweighted mean of 0.37 mg/L for Denton’s detected finished-water entry-point samples from 2012–2019. All 16 samples in that set detected fluoride; the highest was 0.66 mg/L among those finished-water samples from 2012–2019.
| Federal reference | Fluoride level | What it represents |
|---|---|---|
| US Public Health Service recommendation | 0.7 mg/L | Recommended level for community water fluoridation |
| EPA secondary standard | 2.0 mg/L | A non-enforceable federal guideline |
| EPA maximum contaminant level | 4.0 mg/L | An enforceable limit for public water systems |
The 2012–2019 sample mean and maximum were below all three reference levels. The 0.7 mg/L recommendation is not the same kind of benchmark as EPA’s enforceable 4.0 mg/L limit.
The historical mean is not necessarily the level at a particular tap today. It is an unweighted average across entry-point samples, not a measurement taken at every home. The older samples may include unfluoridated sources or predate current practice. They also do not establish the system’s current compliance status.
How does Denton compare with the county and Texas?
According to CDC state and county fluoridation data, 93.6% of Denton County’s public-water-system population received fluoridated water in 2020. The corresponding figure for Texas was 71.0% in 2020.
These percentages describe the population served by public water systems, not necessarily every county or state resident. They are regional context, not measurements of fluoride at a Denton address. The county figure also covers systems beyond the City of Denton utility.
The regional figures and Denton’s utility status come from different reporting years. They should not be treated as a single current snapshot of every water system in the county.
What does Texas law say about fluoridation?
The information reviewed does not establish whether Texas law requires, permits or restricts community water fluoridation. Denton’s reported status alone does not answer what state law requires of other systems.
For current state requirements or local decisions, ask the Texas Commission on Environmental Quality or your water supplier. A supplier can also explain which system serves your address and whether it adds fluoride. The historical EPA measurement by itself cannot establish a state policy.
How can you check or remove fluoride from your water?
Start by identifying your supplier on your water bill, then ask it for its latest drinking water quality report and current fluoride information. If you use a private well, the City of Denton’s utility report will not tell you your well’s fluoride concentration.
For a measurement at your tap, ask a water-testing laboratory for a fluoride test and follow its sampling instructions. Check what the result covers and retain the sampling date so you can distinguish it from the older utility data. Our guide explains how to test water quality at home.
Some reverse osmosis systems, distillers and activated alumina filters can reduce fluoride. Not every product or pitcher does: look for independent certification that specifically lists fluoride reduction, and follow the manufacturer’s replacement and maintenance instructions. Compare options in our guide to the best pitcher water filters.
If you want to check a filter’s performance, a laboratory test of water before and after treatment can help. Boiling is not a fluoride-removal method; evaporation can concentrate fluoride in the remaining water.
Who should ask for advice?
If you have questions about fluoride in your drinking water, ask a dentist or doctor.
Where does the information come from?
The CDC’s 2025 system status identifies whether the City of Denton water system fluoridates; it is a status report rather than a current measurement at your tap. The CDC’s separate 2020 dataset supplies the county and state population percentages.
The EPA’s 2012–2019 compliance dataset supplies the historical finished-water sample results. Those samples provide useful context, but their age, entry-point basis and unweighted mean limit what they can say about water at an individual address now. For a current system-specific answer, contact your supplier; for a tap-specific result, arrange a fluoride test.
Frequently asked questions
What is the City of Denton’s public water system ID?
The City of Denton’s public water system ID is TX0610002.
What does mg/L mean on a fluoride result?
It means milligrams per liter, a unit used to express the concentration of a substance in water.
Does a sample count show how much water residents drank?
No. A sample count tells you how many water samples were included, not how much water residents consumed.