Is There Fluoride in Billings Water?
Yes, fluoride is present: finished-water samples from 2012–2019 had a measured mean of 0.46 mg/L, but whether the utility adds fluoride is not reported.
Does Billings add fluoride to its water?
The available measurements show fluoride in Billings finished water, but they do not establish whether it was added by the utility. Fluoride can occur naturally in water; its presence alone does not prove that a water system practices fluoridation.
The distinction matters when comparing fluoride in tap water by city: a reported concentration and a utility’s fluoridation status answer different questions. The historical Billings measurements answer the first question, not the second.
How much fluoride was measured in Billings water?
The EPA records contain 10 detected finished-water samples for the Billings city system from 2012–2019. Their measured mean was 0.46 mg/L, and the highest detected sample was 0.6 mg/L.
| Measurement or standard | Fluoride level | Basis |
|---|---|---|
| Billings measured mean | 0.46 mg/L | Mean of 10 detected finished-water compliance samples, 2012–2019 |
| Billings highest sample | 0.6 mg/L | Highest detected finished-water compliance sample, 2012–2019 |
| US Public Health Service recommended level | 0.7 mg/L | Recommended level for community water fluoridation |
| EPA secondary standard | 2.0 mg/L | Non-enforceable federal guideline |
| EPA maximum contaminant level | 4.0 mg/L | Enforceable federal drinking-water limit |
Both the historical mean and the highest sample were below all three reference levels. The 0.7 mg/L recommendation is a fluoridation target, not an EPA maximum contaminant level. The 2.0 mg/L secondary standard and the 4.0 mg/L maximum contaminant level serve different regulatory purposes.
These historical samples do not establish the fluoride concentration at a Billings tap today. They also should not be used on their own to determine the system’s current regulatory compliance.
What do county and state figures show?
Billings is in Yellowstone County, Montana. A county-wide percentage of people receiving fluoridated water is not available in these records, so the Billings sample results should not be treated as a county-wide figure.
In 2020, 31.4% of Montana’s population served by public water systems received fluoridated water, according to the CDC’s state and county fluoridation data. That statewide percentage does not establish the status of Billings or any particular Yellowstone County water system.
A household’s result depends on its water source. City-system sampling does not describe every other public supply or private well in the county.
What is Montana’s fluoridation policy?
The records cited here do not establish Montana’s statewide policy on adding fluoride to public water supplies. The state percentage describes how many people received fluoridated public water in 2020; it does not, by itself, identify a legal requirement or explain individual utility decisions.
For the current policy or the Billings utility’s present practice, ask the utility or the appropriate Montana drinking-water authority. In particular, ask whether fluoride is added and request the date to which the answer applies.
How can you check or remove fluoride in your water?
First, identify your water supplier. If you receive Billings city water, ask the utility for its latest water-quality report and a current fluoride result. Ask whether the result represents finished water at the treatment plant or a sample from another point in the distribution system.
If you use a private well or another supplier, obtain a result for that source rather than relying on the Billings city samples. A laboratory that tests drinking water can explain its sampling instructions and report fluoride in mg/L. Our guide to how to test water quality at home explains how to approach testing.
To reduce fluoride, look for a treatment system independently certified for a fluoride reduction claim. Reverse osmosis systems can be certified for that purpose, but do not assume every filter or pitcher removes fluoride. Compare the specific claims on the product and follow its installation and cartridge-replacement instructions; our guide to the best pitcher water filters can help with the comparison.
If you want to check a filter’s performance, ask a laboratory about testing water before and after treatment. The Billings historical mean is not a substitute for either measurement.
Who should you ask about fluoride?
If you have questions about fluoride in your drinking water, ask a dentist or doctor.
Where do the Billings figures come from?
The Billings measurements come from the EPA’s Six-Year Review 4 compliance monitoring data for 2012–2019. The fluoride summary identifies the system as BILLINGS CITY OF, ID MT0000153, and records 10 finished-water samples, all with detections.
The mean describes those detected samples, not a continuous measurement over the entire period or a guaranteed concentration at every tap. The CDC figure is a separate statewide estimate for 2020; it is not a measurement of fluoride concentration in Billings water.
Frequently asked questions
What does mg/L mean on a fluoride report?
It means milligrams per liter, a measure of the amount of fluoride in a volume of water.
Does boiling water remove fluoride?
No. Boiling does not remove fluoride and can increase its concentration as water evaporates.