Is There Fluoride in Bakersfield Water?
No fluoride is added; the reported Bakersfield water system contains natural fluoride only, with a measured mean of about 0.25 mg/L in 2012–2019.
Is fluoride added to Bakersfield water?
The CDC’s 2025 report identifies CWS - Bakersfield as not fluoridated, with a status of Non-Adjusted. That means the system is not reported as adding fluoride to adjust its concentration; it does not mean the water contains no fluoride.
Federal sampling found fluoride in the system’s finished water. For a broader comparison, see fluoride in tap water by city. The Bakersfield status applies to the reported system, so check your own supplier before assuming it describes every address in the area.
How much fluoride was measured in Bakersfield water?
The EPA’s 2012–2019 compliance data show a mean of 0.25 mg/L for detected finished-water samples from CWS - Bakersfield. Fluoride was detected in all eight samples, and the highest measured result was 0.34 mg/L in the same 2012–2019 dataset.
| Measurement or standard | Fluoride concentration | Basis |
|---|---|---|
| Bakersfield mean | 0.25 mg/L | Mean of detected finished-water compliance samples, 2012–2019 |
| Bakersfield maximum | 0.34 mg/L | Highest of eight finished-water compliance samples, 2012–2019 |
| US Public Health Service recommendation | 0.7 mg/L | Recommended level for community water fluoridation |
| EPA secondary standard | 2.0 mg/L | Non-enforceable secondary standard |
| EPA maximum contaminant level | 4.0 mg/L | Enforceable drinking-water limit |
Both the historical mean and maximum were below all three reference levels. The 0.7 mg/L figure is a recommendation for systems that fluoridate their water, not a requirement that a non-adjusted system reach that concentration.
These are historical system-level results, not a current measurement from every tap. The concentration at your address may differ, so use a recent supplier report or a test if you need an up-to-date figure.
How does Bakersfield compare with Kern County and California?
In 2020, 4.0% of Kern County’s public-water-system population received fluoridated water, compared with 57.5% across California. These percentages describe populations served by public water systems, not the percentage of suppliers that fluoridate or the concentration in an individual glass of water.
The county figure is context rather than a separate measurement of CWS - Bakersfield. The state and county figures also cover a different year from the Bakersfield system’s 2025 status report and may have changed since 2020.
What does California law say about fluoride in Bakersfield water?
The records behind these figures do not identify a California fluoride policy or establish how a state law applies to CWS - Bakersfield. The statewide percentage alone does not tell you what any law requires or whether every water system follows the same practice.
For current policy, ask California’s drinking-water regulator or your water supplier. When asking, identify your water system and request the current rule or public record that applies to it. A system’s reported fluoridation status and a state-level policy are separate pieces of information.
How can I check my water or remove fluoride?
Check your supplier and its report
Start with your water bill or your supplier’s consumer confidence report to identify the system serving your address. The system in the CDC and EPA records here is CWS - Bakersfield, ID CA1510003; an address in the Bakersfield area could have a different supplier or a private well.
Look for fluoride in the latest report, along with the sampling year and the units. A supplier report gives system-level information, but it may not tell you the exact concentration at your tap. Our guide to how to test water quality at home explains how to approach testing.
Test your tap water
For a result specific to your address, ask a qualified drinking-water laboratory for a fluoride test. Follow its instructions for collecting and submitting the sample, and ask for the result in mg/L so you can compare it with the reported values and standards above.
If you use a private well, a tap or well-water test can give you information that a public supplier’s report cannot. Keep the sampling date with the result; a historical system average is not a substitute for a current sample.
Choose a filter for fluoride reduction
If you want to reduce fluoride, check the exact filter model for independent certification specifically for fluoride reduction. A reverse-osmosis system certified to NSF/ANSI 58 for that claim is one option. Follow the manufacturer’s maintenance and replacement instructions.
Do not assume every pitcher, refrigerator or carbon filter removes fluoride. Compare the best pitcher water filters, but check each model’s certified reduction claims before choosing one. If you want to verify a filter’s performance at home, ask a laboratory about testing untreated and treated samples.
Who can answer questions about fluoride?
If you have questions about fluoride in drinking water, ask a dentist or doctor.
Where do these figures come from?
The CDC’s 2025 fluoridation status report lists CWS - Bakersfield as not fluoridated and Non-Adjusted. It identifies the status of that system, rather than measuring the water at an individual address.
The EPA’s Six-Year Review 4 compliance data contain the eight 2012–2019 finished-water samples used for the Bakersfield mean and maximum. All eight samples had detectable fluoride.
The CDC’s state and county fluoridation dataset supplies the 2020 Kern County and California population percentages. Those figures provide geographic context; they are not a replacement for a current report from your own supplier.
Frequently asked questions
Can boiling remove fluoride from Bakersfield water?
No. Boiling does not remove fluoride, and evaporation can increase its concentration in the remaining water.
How does mg/L compare with parts per million?
For dilute water samples, 1 mg/L is approximately equal to 1 part per million, or 1 ppm.